Click the " eagle " engraving equipment → support HPGL commands engraving machine or MULTICAM610PLUS connected serial port 1 or serial port 2 → carrying knives height → 3mm ( can root
Click the " eagle " engraving equipment → support HPGL commands engraving machine or MULTICAM610PLUS
Connected to serial port 1 or serial port 2 → carrying knives height → 3mm ( height can be determined according to the actual situation of carrying knives )
Click the "Settings" 1, set ports: serial port 1 or serial port P → 2 → 8 data bits Stop bits → 1 parity : NONE transfer rate → 9600
Flow control → √ DTR / DSR √ XON / XOFF √ RTS / CTS
2 , "Setting engraving machine" carrying knives command , drop the knife command → 3 parameters Spindle positive Z axis resolution down → → GV series engraving machine for the 2540 lines / inch , HGV engraving machine for the 4064 lines / inch
Carrying knives from → 3mm ( carrying knives height can be determined according to the actual situation ) carving tool rotation direction clockwise output compensation → → No
3 , set the " format and origin" maximum width , length can be determined based on the actual level of the Z-axis and vertical resolution and the same resolution , namely : GV series engraving machine for the 2540 lines / inch , HGV engraving machine for the 4064 lines / inch ( which early Edition 2032 HGV 5.5 lines / inch ) at the coordinate origin - the left one , to stop the knife at the moment → left after a paper advance direction is the X direction.
4 , the command set is initialized IN; PA; PU0, 0, -300; ( Note: both Arabic numerals 0 ) ! Drop the knife go PD carrying knives go PU separator , homing PG; terminator ; rest with the software defaults to complete after clicking OK. Wentai engraving software can be directly output , wherein F: The mirror , which outputs the contents of the Y -axis direction of the full- mirror ; R: Representative rotation, the rotation select the output full- time content 90 degree rotation.
The first step : maintop → install → install → OK → OK → Select "Do not start your computer " → completed
Step two : maintop → change → setup → setup → start → ok.
The third step : maintop → change → change driver, copy the three files inside the C: DTP DRIVER folder.
Setup: Start → Programs → select Thai color electronic publishing systems Monteiro sent to the desktop icon , open Monteiro → File → Settings → Printers → choose to install a new printer Monteiro 'Jetposter'3330 → → install a new printer as the default printer → Close → confirm.
To start the installation
1 , run the installation CD Type3V4200 program Setup, select "Next" or "Yes", until the installation is complete.
2 , run CD crack1, click Apply to determine the decryption software , if you have "crack 2", please do the same operation.
3 , Type3 default installation path is : C: Vision, if you want to change the installation path , change the drive letter name only , do not change the drive letter after the ": Vision", after the change the installation path , running crack1 decryption , must be modified to do the same , the same letter name change only , do not change " : " default path after .
4 , some versions of the CD crack is compressed, after decompression run. Some older versions of the CD-ROM does not crack file , locate the "EXE" folder in the CD-ROM , copy and paste to the Type3 installation directory to replace the original EXE.
5 , in some versions of the operating system that will run with the installation of some software , such as Type3 "Setup" screen after stopping , and may pop up error log reports , then please delete the system font folder where non-system fonts the end of the software and then reinstall the font .
Type3 settings
After the initial installation Type3, woodpeckers DSP or ARM for each model , please set the following order , if you are using a Hdtaoye or Ncstudio each version control system, you do not have to set item 3 below .
1, open on the desktop or in a program Type3, open the " Settings machine" , click on " add machine" before the " + " sign , then expand "CNC machine" , find "Fanuc 16M/Fanuc 0M" and select , click " Join ."
2, in the "Settings Interface" select " File" and OK.
3 , open the "Settings machine" dialog box , first open the right of the " post-processor " , find the following line in the word " after setting the processor," in : ...... HeadpcrSz0 = p HeadpcrSz1 = G91 G28 Y0 Z0 HeadpcrSz2 = t HeadpcrSz3 = M6 ......... these four lines of characters after the equal sign is amended as follows : ...... HeadpcrSz0 = 0
HeadpcrSz1 = 0 HeadpcrSz2 = 0 HeadpcrSz3 = 0 ...... confirmed modify and correct.
Back to " set the machine ", the minimum and maximum respectively modify the " total size" under the following:
x Minimum :-20000.00mm Maximum : 20000.00mm
y Min :-20000.00mm Maximum : 20000.00mm
z Minimum :-10000.00mm Maximum : 10000.00mm
Units are in millimeters : mm, confirm and exit "Set the machine ."
5, Type3 software to open , open the " Options" , " Edit" under modified as follows :
( 1 ) , " Calculation Parameters " , select the "path to" "artificial " under ; check the " Auto melted ."
( 2 ) " page can be engraved " in which each of the width, height , depth, to format the size of the machine , such as RS1212 type , a width of 1200mm, a height of 1200mm, a depth of 110mm, the others are 0 , the unit is mm : mm. OK.
6 , open the "Change" , " page can be carved ," under which the depth of the width and height to make modifications as above , and the rest are 0.
7 , Type3 do any graphic into the "CAM" create any tool paths , machine work . In the " machine work ", the following modifications :
( 1 ) , open the " share ", check " curve line " and the "Z security start bit " was changed to 1mm.
( 2 ) , in the " machine work " dialog, activate the " lock " symbol , click on "File" , OK.
( 3 ) , modify the " machine work " parameter box center position is 5-10 , this is the process of carrying knives height.
8 Save and close Type3, software set the end .
The above settings are Type3 after the initial installation must be set after the completion of each set do not need to use this setting , if the machine does not read the file appears engraving work or alarm error , please check the above settings are correct . Notes 1, CF card or U disk DSP advertising engraving machine can not work with any non-working file , not a virus . Viruses are generally in the form of hidden files exist, use the latest version of the killing of anti-virus tool , you need to reinstall the operating system when necessary , failure is generally caused by the virus likely reason being given for the work , beyond the scope , do not even read the disk and so on.
2, U disk work used when doing formatting, "File System" must choose "FAT", or it may not read the disk engraving machine work .
3 , certain brands of CF card or U disk because of compatibility problems that may lead to the engraving machine does not work or read the disk crashes , replace the CF card or U disk other brands . Special Note
If the computer has already installed Type3, please uninstall Type3 original components, uninstall as follows:
Under WinXP or Win2000 operating system , open the " My Computer" - "Control Panel" - " Add / Remove Programs " in the " Currently installed programs ", select Type3 Ver 4.2.00, click " Change / Remove (c) "and then select the required " Yes To All " and " Ok " to complete the deletion .
mini cnc milling machine
cnc milling machine
4 axis cnc router
hot sale mini cnc router
mini cnc engraver